Contact Us

 

We have come across this article on Tools You Need to Install a New Bathtub down the page on the net and figured it made sense to discuss it with you on my blog.

Installing a bathtub isn't precisely brain surgery, yet it does need solid plumbing, carpentry, and often, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult task. If the old tub is conveniently obtainable, the job can relocate easily; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the job and also are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Chances are you may require an expert plumber to make tube links.
This post will certainly help you mount a brand-new tub in your shower room if you have actually already bought a new bathtub and do not require to change the setup of your previous water supply pipelines.
Your tools and also product checklist should make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Getting ready for the Installment

To start with, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid strain on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last setting.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, switch on the faucets to drain any water remaining in the system. The process of getting rid of the existing taps can be rather troublesome because of the restricted access that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel ready for the remaining water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. Once the taps have been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Mounting the Bath tub

Making use of both wood boards under its feet, position the tub in the called for position. The wood boards are useful in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level as well as adjusting the feet on the bathtub till the spirit level reads level.
To install taps, fit all-time low of the outermost flexible tap port to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages as well as tighten them if required. Fill the tub and also examine the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub must wait till the bathtub has been used a minimum of when as this will resolve it right into its final position.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making certain that the washers are in location in between the faucet and also the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind should be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bathtub

In the location where the bathroom fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break a rigid seal, triggering the water to penetrate the wall between the bathroom and the tiling, leading to complications with dampness and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the tub with water prior to sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly offered on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or water resistant glue as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I discovered that blog post about Tools You Need to Install a New Bathtub when looking around the web. Loved our article? Please share it. Let other people check it out. I take joy in reading our article about A Step-by-Step Guide to Installing a Bathtub.

Trusted for emergency plumbing excellence.